iFlight Chimera4 LR Sub 250g FPV Drone 4S GPS Caddx Nebula Digital HD System PNP
Introducing our first ultra-light LongRange 4inch BNF for every terrain. Newest iFlight SucceX hardware on board coupled with our XING 1404 motors in different kv classes. Slow crusing or speedy action, theres something for every taste. Get flight times above 15min using at least 4S 850mAh packs. Go crazy and strap a Li-On 4S pack on and go even further, depending on capacity and weight!
GPS Rescue ready for easy recovery in case of signal loss, or even if you've been surfing those mountains and suddenly can't find the way back home.. Betaflight OSD pre-setup GPS elements will show you the way!
CaddX Vista with two optional cameras available. Original DJI Vista cam or the lighter and smaller CaddX Nebula.
Outstanding digital FPV experience in 720p directly on your goggles. Custom iFlight 150mm LR antenna for best signal coverage even at long distance.
HIGHLIGHTS:
Sub 250g long-range quad
XING 1404 3000KV(Crusiser) / 3800KV (Speed Cruiser) Ultralight motors
X-Geometry body for high performance handling and max. authority on pitch axis
DC (DeadCat geometry) bottom plate available (additional item, not included, no props in view)
GPS pre-installed for more safety at distance
SucceX-E mini F4 +35A 4in1 ESC Flystack
Naked GoPro ready
360° TPU protection, Vista cam protection and antenna mounts
Caddx Vista Digital HD System / Caddx Nebula Digital HD System
PRE-TUNED & PRE-SETUP:
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"
GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour.
Please check our linked article on "GPS Rescue Mode // Setup"
FRAME // ：Chimera4
Wheelbase: 178mm
Main body dimension: 136.8*114.8mm
Bottom to top distance: 28mm
Arm thickness: 4mm
Bottom plate thickness: 4mm
Top plate thickness: 2mm
TPU Camera plate thickness: 2mm
FC: 25.5*25.5mm/20*20mm/16*16mm
FPV Cam: 19mm Micro / 20mm
ELECTRONICS // SucceX-E mini F4 Stack (35A 4-in-1 ESC)：
SucceX-E mini F4
MCU: 168MHz STM32F405
Gyro: MPU6000
Blackbox: 8MB
Betaflight OSD: YES
BEC: 5V 2.5A
Uarts: 4
ESC Telemetry: yes
INA Pad: nuart2
Input voltage: 2-6S
Size: 25*25mm /20*20mm φ3 mounting
Weight: 4g
Firmware: BETAFLIGHTF4
Physical
Mounting hole: 20*20mm，φ3mm
Size: 25*25mm
NOTE: F.PORT protocol RX input support, telemetry not supported.
ESC // SucceX-E mini 35A
MCU: BB21 F16G
BLHeliS
Capacitance: 470uF/50V
Current Sensor: Yes
Input: 2-6S LIPO
Constant: 35A / Burst: 40A
BEC: No
Supports up to Dshot600, Proshot, Oneshot, Multishot
Target: G-H-30
Weight: 6.9g
Mounting pattern: 20*20, φ3mm with Grommets φ2mm
Dimensions: 31*30mm (including the power pads)
BNF // Parts list (Build)
Prebuilt and indoor tested Quadcopter
1x Chimera4 frame
1x Caddx Nebula Digital HD System（as your choice）
1x Albatross LHCP ipex 160mm antenna
1setx Nazgul 4030 props (Set of 2 - Color may vary)
1setx Gemfan 4024 Props (Set of 2 - Color may vary)
2x 15*150mm Microfiber PU Leather Battery Strap (Color May Vary)
