HappyModel Mobeetle6 Toothpick Whoop FPV Drone SPI FrSky ELRS

HappyModel Mobeetle6 Toothpick Whoop FPV Drone ELRS

Rs. 9,200.00
Save Rs. 1,500

Quantity

Featured Products

RadioMaster Bandit Nano ExpressLRS 915MHz RF ELRS 1W Module TX

Rs. 3,600.00 Rs. 4,400.00

DOGCOM 5200mAh 6S 120C 22.2V LiPo Battery QS8 [DG]

Rs. 10,200.00

ISDT K2 Air Dual Channel Smart Charger 2-6S AC DC 200w 500w 20A

Rs. 11,700.00 Rs. 13,300.00

TBS Crossfire Micro TX V2 Starter Set

Rs. 9,500.00

TBS Crossfire Diversity Nano RX

Rs. 4,100.00

Infinity 1400mAh 6S 150C 22.2V LiPo Battery XT60 [DG]

Rs. 2,600.00

HappyModel Mobeetle6 Whoop Toothpick 65mm 2IN1 FPV Racing Drone BNF ELRS

Please note that if your ELRS Radio Controller is V3, the BetaFlight Target Firmware on the drone need to be upgraded for ELRS 3.0 Binding purpose, please find the firmware and CLI Dump file from the link below:

HappyModel Mobeetle6 SPI ELRS 3.0 Firmware + CLI Dump

You will need to FLASH the firmware and APPLY the CLI Dump file to the drone.

The new Mobeetle6 BNF would be the lightest 65mm mass production whoop in the world, hope you will enjoy it . The DiamondF4 Flight controller and 0702 motors were inspired from Angry Don FPV, we really appreciated for his help to Happymodel and to this hobby. We also very expecting to the performance of this BNF with the new Diamond F4 ELRS flight controller.

Specifications:

Brand Name: Happymodel
Item Name: Mobeetle6 whoop and toothpick 2-IN-1 FPV Racer Drone
Wheelbase: 65mm
Size: 80mm*80mm*30mm
Weight: 17.5g (without battery)

Features:

The lightest 1S Whoop and Toothpick 2-IN-1 fpv drone
Comes with tooth pick frame for convert
Powerful and efficiency
The lightest 1s AIO 5IN1 F4 flight controller
New Unibell SE0702 brushless motors with pcb wire board
Built-in OPENVTX up to 400mw
Low profile Canopy design

Spare parts specifications:

Motor

Model:SE0702 KV23000
Configu-ration:9N12P
Stator Diamter:7mm
Stator Length:2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.*Len):Φ9.5mm*14mm
Weight(g):1.5g
No.of Cells(Lipo):1S only

Propeller

Weight:0.19g
Material:PC
Pitch:1 inchProps Dia:30mm
Center Hole Dia:1mm

Flight Controller

(ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280
(Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OPEN VTX
Built-in SPI ELRS V2.0/Frsky receiver
Built-in 5V 1A BEC

Onboard 4in1 ESC

MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_50_REV16_8.HEX
Default protocol: DSHOT600

Onboard SPI ExpressLRS 2.4GHz Receiver

Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX Module
Couldn’t flash separately ExpressLRS firmware

Onboard Frsky SPI D8 receiver Version

SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 modelChannels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m